Welded Wire Mesh,Welded Mesh,Galvanized Welded Wire Mesh Gabion And Mattress,Stainless Steel Wire Mesh Co., Ltd. , http://www.chwire-mesh.com
Qualified materials crushed will be screened out and exit from the gap of the grate bars while the unqualified will be left in the crushing cavity to be further hammered and ground until reach the standard size. The size of the final product can be adjusted by changing the grate bars. The gap between the rotors and the grate bars can also be adjusted according to different requirement. To avoid the plugging of the crusher, the proportion of water for the crushing materials is no more than 20%.
When the hammer crusher or hammer crushing machine works, the motor drives the rotor to spin at high speed, materials are fed into the crushing cavity evenly, and then be impacted, cut and tore by high speed spinning hammerhead till they are completely crushed. Meanwhile, the gravity action of materials forces them to crash the baffle and grate bars on the frame. Materials with particle size smaller than the screen size will pass the sieve plate while those with bigger particle size are stopped on the plate and will continue to be impacted and grounded by the hammer until they are crushed to the required particle size, finally, crushed materials will be discharged from the hammer crusher through the sieve plate.
Instruction:
Hammer crusher is generally used to crush materials whose size is in 600-1800mm into around 25mm.Hammer crusher is mainly adopted in cement, chemistry, electricity and metallurgy industry, especially for crushing finely. Hammer crusher is mainly composed by box, roller, hammer, counterattack plate and screen etc,.The crushed materials are generally coal, salt, chalk, plaster, brick and tile, limestone etc. It is also used to crush fiber, elastic broken wood, papers and waste. On the other hand, hammer crusher is also could replaced with cone crusher.
Â
model
Max feed size
(mm)
Output size
(mm)
Capacity
(T/h)
MotorÂ
Power(kw)
PC70
100-150
≤20
15-25
30
PC90
100-150
≤20
30-60
45
PC120
100-200
≤20
50-90
55
PC135
100-200
≤20
60-100
75
PC150
100-200
≤20
90-120
110
PC180
100-300
≤25
100-150
150
PC210
100-300
≤25
120-180
220
Hammer crusher mainly consists of frame, rotor, support iron and grate bars. The frame is divided into two parts: upper part and lower part, which are welded by steel plates after being cut. Liners made of high manganese steels within the frame can be replaced after being worn out.The rotors consist of turn plates, pin shafts, and hammers which are grouped regularly in the main shaft. The main unit drives the main shaft through the motor and triangle belts, which, in turn, rotates the rollers. Large materials entering the crusher through the feed inlet are firstly crushed by the high-speed hammers, and then thrown fiercely to the support iron for further crushing.
Qualified materials crushed will be screened out and exit from the gap of the grate bars while the unqualified will be left in the crushing cavity to be further hammered and ground until reach the standard size. The size of the final product can be adjusted by changing the grate bars. The gap between the rotors and the grate bars can also be adjusted according to different requirement. To avoid the plugging of the crusher, the proportion of water for the crushing materials is no more than 20%.
When the hammer crusher or hammer crushing machine works, the motor drives the rotor to spin at high speed, materials are fed into the crushing cavity evenly, and then be impacted, cut and tore by high speed spinning hammerhead till they are completely crushed. Meanwhile, the gravity action of materials forces them to crash the baffle and grate bars on the frame. Materials with particle size smaller than the screen size will pass the sieve plate while those with bigger particle size are stopped on the plate and will continue to be impacted and grounded by the hammer until they are crushed to the required particle size, finally, crushed materials will be discharged from the hammer crusher through the sieve plate.
Instruction:
Hammer crusher is generally used to crush materials whose size is in 600-1800mm into around 25mm.Hammer crusher is mainly adopted in cement, chemistry, electricity and metallurgy industry, especially for crushing finely. Hammer crusher is mainly composed by box, roller, hammer, counterattack plate and screen etc,.The crushed materials are generally coal, salt, chalk, plaster, brick and tile, limestone etc. It is also used to crush fiber, elastic broken wood, papers and waste. On the other hand, hammer crusher is also could replaced with cone crusher.
Â
model
Max feed size
(mm)
Output size
(mm)
Capacity
(T/h)
MotorÂ
Power(kw)
PC70
100-150
≤20
15-25
30
PC90
100-150
≤20
30-60
45
PC120
100-200
≤20
50-90
55
PC135
100-200
≤20
60-100
75
PC150
100-200
≤20
90-120
110
PC180
100-300
≤25
100-150
150
PC210
100-300
≤25
120-180
220
Model NO.: PCF-240
Inlet Size: 600×900mm
Condition: New
Trademark: TSDC
Transport Package: No
Specification: PCF-240
Origin: Tangshan
HS Code: 84742090
Model NO.: PCF-240
Inlet Size: 600×900mm
Condition: New
Trademark: TSDC
Transport Package: No
Specification: PCF-240
Origin: Tangshan
HS Code: 84742090
Hammer crusher mainly consists of frame, rotor, support iron and grate bars. The frame is divided into two parts: upper part and lower part, which are welded by steel plates after being cut. Liners made of high manganese steels within the frame can be replaced after being worn out.The rotors consist of turn plates, pin shafts, and hammers which are grouped regularly in the main shaft. The main unit drives the main shaft through the motor and triangle belts, which, in turn, rotates the rollers. Large materials entering the crusher through the feed inlet are firstly crushed by the high-speed hammers, and then thrown fiercely to the support iron for further crushing.